Narrow-beam divergence 1.3-μm multiple-quantum-well laser diodeswith monolithically integrated tapered thickness waveguide

This paper describes the optimum design, fabrication, and performance of a 1.3-μm multiple-quantum-well (MQW) laser diode monolithically integrated with a tapered thickness spot-size transformer. The dependence of the lasing characteristics on the thickness distribution of the core layer and on the current injection profile of the device were analyzed. This integrated laser with its optimized structure performed at a low threshold current of 22.2 mA, even at 85°C. The integrated spot-size transformer effectively reduced the lateral and vertical far-field FWHM's to 8° and 9°, respectively. A very long lifetime of over 1×10⁵ h was estimated at 85°C and 8 mW under CW operation     

Design of experiments for stacking sequence optimizations with genetic algorithm using response surface approximation

This study describes a new method of experimental design to obtain a response surface of buckling load of laminated composites. Many evaluations for genetic algorithms for stacking sequence optimizations require high computational cost. That evaluation cost can be reduced by an approximation using a response surface. For a response surface for stacking sequence optimizations, lamination parameters are adopted as variables of the approximation function of the entire design space instead of ply angles for each ply. This study presents, proposes and investigates a new method of experimental design in detail. For most analytical tools, stacking sequences is demand as input data and lamination parameters cannot be applied directly to the tools. Therefore, the present study proposes and applies a new D-optimal set of laminates to the stacking sequence optimizations of the problem of maximization of buckling load of a composite cylinder. The new experimental design is a set of stacking sequences selected from candidate stacks using D-optimality. Consequently, the D-optimal set of laminates is shown to be effective for design of experiments of response surfaces for maximization of the buckling load of composite structures.     

Hydraulic Study of the Onset of Hypoxia in the Tone River Estuary

Field measurements were conducted to investigate the onset and growth of hypoxia in the Tone River Estuary. Vertical profiles of dissolved oxygen (DO), salinity, and temperature were measured along the deepest line of the estuary. Rates of oxygen consumption by water and sediment in a salt wedge were obtained using laboratory tests. The measurements showed that hypoxia frequently occurred in the front part of the salt wedge and expanded its area toward the river mouth during the summer when the river flow rate was small. The data also suggested that the onset of hypoxia was delayed by the estuarine circulation which supplied oxygen-rich seawater to the salt wedge. To simulate this phenomenon, a two-dimensional flow model in the vertical-longitudinal plane was constructed by transversely integrating the k–ε model equations. The results of model simulation for three months in the summer of 1997 closely matched the field data. The model simulation proved that DO degradation is highly correlated with the residence time of salt water in the estuary.     

Numerical computation of two-loop box diagrams with masses

A new approach is presented to evaluate multi-loop integrals, which appear in the calculation of cross-sections in high-energy physics. It relies on a fully numerical method and is applicable to a wide class of integrals with various mass configurations. As an example, the computation of two-loop planar and non-planar box diagrams is shown. The results are confirmed by comparisons with other techniques, including the reduction method, and by a consistency check using the dispersion relation.     

Fabrication of octacalcium phosphate block through a dissolution-precipitation reaction using a calcium sulphate hemihydrate block as a precursor

Although octacalcium phosphate (OCP) powder and a collagen/gelatin composite demonstrate good potential as bone substitutes, an OCP block has not been fabricated to date. In this study, the feasibility of fabricating an OCP block was evaluated through a dissolution-precipitation reaction using a calcium sulfate hemihydrate (CSH) block as a precursor. When the block was immersed in a phosphate salt solution, its composition changed to that of OCP, while its structure was maintained. The diametral tensile strength (DTS) of the OCP block was 1.0?±?0.2?MPa. The macroporosity and microporosity of the OCP block were 33.4?±?4.5% and, 69.0?±?1.6%, respectively. New bone attached well to the OCP block, and this block was partially replaced by bone 2 weeks after implantation. Four weeks after implantation, the surface of the OCP block was nearly covered with new bone and ~30% of the block was replaced by new bone, while no replacement by bone was observed in the case of a hydroxyapatite (HAp) block used as a control. It is concluded that OCP blocks are potentially suitable for their use as artificial bone substitutes.     

Performance Comparison of Circuits for Pole‐Mounted STATCOM Using SiC Devices

The recent years have seen an increasing trend in the cumulative installed capacity of distributed generators. As a result, voltage management may become difficult in existing power distribution systems in the future. A STATCOM (STAtic synchronous COMpensator) is a promising option for solving this problem because it can control reactive power rapidly and continuously. For a distribution system, STATCOM needs to be pole‐mounted to realize its low cost. However, a transformer for a STATCOM is large and heavy, and hence it is difficult to install a STATCOM on a distribution pole. We adopt a transformerless STATCOM to reduce STATCOM size and use SiC devices with low‐loss performance to obtain a more compact and efficient STATCOM. There are a large number of circuits available for a STATCOM, and there has been considerable research on performance comparisons among these circuits. However, these comparisons were drawn under different conditions, including switching frequency and level number for the circuits. In addition, these comparisons do not include the use of SiC devices. We made an equitable comparison for a 100 kVa pole‐mounted STATCOM using SiC devices. We discuss the performance and characteristics of each circuit in terms of efficiency and volume.     

Study of Cuprate Superconductivity Using the Particle Number Conserving Bogoliubov-de Gennes Equations: ARPES and STS Images From Surface Plus Bulk Layers Model

Journal of Superconductivity and Novel Magnetism - We theoretically study the superconductivity in hole-doped cuprate superconductors by employing a model composed of surface and bulk CuO $$_2$$...